topleft1.gif (2468 bytes) topleft2.gif (2164 bytes) topleft3.gif (1774 bytes)

 

 

 

 

1.
TA-553 Camera Adaptor
 
1)
Input Signals
 
• Microphone 

-60 dbs to -40 dbs 600 Ohm 2 channels (One channel is supplied from the camera head)

The MIC IN connector of the camera adaptor can be switched
either to +12 V AB powering, +48 Phantom powering or power off.
 
• Intercom

—16 dBs 2 channels (ENG / PROD)

 
2)
Output Signals
 
• Return Video
 VBS
1.0V

positive 75 Q 1 output (RET-i I RET -2 switchable)

• Programmable Audio
0 dBs

2 channels

• Intercom
 0 dBs

2 channels (ENG / PROD)

 
 
2.
BS-553 Base Station
 
1)
Input Signals
 
• External Sync
VBS
1 Vp_p
75 ohm bridge possible
(or BBS 0.45 V)
 
• Return Video
VBS

1 Vp-p

75 ohm 2 channels bridge possible 
• ED Monitor
VBS
1 v
75 ~
• Tally
 R, G
2 channels contact or power supply
• Programmable Audio
0 dBm

600 ohm

2 channels
•
Intercom
(2-wire I 4-wire / RTS switchable)
2-wire
0 dBm
600 ohm
1 channel (ENG)
4-wire
 0 dBs
high impedance
2 channels (ENG / PROD)
RTS
 1 V pp
high impedance
2 channels (ENG/PROD)
RCP-30 Intercom Jack

—l6dBs

 
 
 
 
 
 
 
 
 
2)
Output Signals
 
• Composite Video
VBS
1 Vp-p
positive 75 ohm 3 outputs
 
(SYNC ON / OFF possible)
 
• RGB
0.714 ~ positive 75 Q 1 output each
 
•
Component (Y / R-Y / B-Y)
 

Y

  vs

i1vp-p

75 ohm 1 output

 

R-Y, B-Y    v

0.756 Vp-p (f3)
75 ohm, 1 output each
 
(or o.525vp-p (MII)
 
• Video Monitor
vs / VBS 1 vp_p
positive 75 ohm 1 output
• Waveform Monitor
 
VS/VBS
1 vp_p positive 75ohm 1 output
 
•
Waveform Monitor control 
SEQ ON, EXPAND ON, STAIR CASE signals
 
 
•
Tally (for video monitor) 
R, G
2 channels contact supply
 
 
• Microphone
0 dBm
600 0

2 channels

 
 
•
Intercom
   
 
(2-wire I 4-wire / RTS switchable)
  		 
 

2-wire

0 dBm
600 0
1 channel (ENG)
 
 

4-wire

 
0 dBrn
600 0
2 channels (ENG / PROD)
 
 

RTS

1 VN~
200 0 load 2 channels (ENG I PROD)
 
 

RCP-30 Intercom Jack

0 dBs
ENG only
 
3.
Power Requirements
   
 
1)
AC Input Voltage
:
100VI117V/220V/240V switchable
50 Hz /60 Hz approx. 200 VA
 
4.

Ambient Temperature and Humidity

  		 
 
1)
Camera Adaptor
:
—20°C to +45°C, 10%~—9O%
 
 
2)
Base Station
—20°C to +45°C, 10%—90%
 
5.
Weight
   
 
1)
Camera Adaptor
:
Approx. 2.5 kg (5 lb 8 oz)
 
 
2)
Base Station
Approx. 18.5 kg (40 lb 12 oz)
 
6.
Control Items
   
 

The functions which can be controlled at the RCP-30 remote control panel in the base station are as follows.

 
 
 
   
 
1)
ON/OFF Controls
   
 
MONITOR SELECT
 
R, G, B, SEQ, ENC
 
 
AUTO IRIS
    
 
PM IND/PAGE
    
 
AWB
Ach, Bch, OFF, HEAD
 
 
CAL
    
 
BARS
    
 
AUTO KNEE
    
 
CALL
    
 
AWB
    
 
ABB
    
 
GAIN
—3 dB, 0 dB, + 3 dB, +6 dB, +12 dB (dependeds on connected camera head)
 
 

BLK STRETCH

 
OFF, 1, 2, 3
 
 

SHUTTER

OFF, 1, 2, 3, 4, 5 (each OFF, 1/100, 1/120, 1/500, 1/250, 1/2000 sec)
,
 
LOCK/UNLOCK
    
 
PANEL ENABLE
    
 
REMOTE / LOCAL
    
 
LOCK I UNLOCK
  
2)
Analog Controls
   
IRIS
 
 
MASTER PED
    
R, B GAIN
    
R, G, B BLACK (Flare or Pedestal)
    
KNEE POINT
    
KNEE SLOPE
    
DTL
    
H PHASE
    
SC PHASE COARSE
    
SC PHASE FINE
    
ENC VIDEO LEVEL
    
ENC CHROMA LEVEL
    
The following items provide remote control possibility as a standard feature.
 

a) IRIS CONT

   

b) MASTER PED CONT

   

c) R, B GAIN CONT

   

d) R, B PED CONT

   

e) R, G TALLY INDICATOR

   

Note Some of the above items may not be controlled depending on the camera connected.